dcb-apptrust(8) — Linux manual page

DCB-APPTRUST(8)                   Linux                  DCB-APPTRUST(8)

NAME

       dcb-apptrust - show / configure per-selector trust and trust
       order of the application priority table of the DCB (Data Center
       Bridging) subsystem.

SYNOPSIS

       dcb [ OPTIONS ] apptrust { COMMAND | help }

       dcb apptrust show dev DEV [ order ]

       dcb apptrust set dev DEV [ order SEL-LIST ]

       SEL-LIST := [ SEL-LIST ] SEL

       SEL := { ethtype | stream-port | dgram-port | port | dscp | pcp }

DESCRIPTION

       dcb apptrust is used to configure per-selector trust and trust
       order of the Application Priority Table, see dcb-app(8) for
       details on how to configure app table entries.

       Selector trust can be used by the software stack, or drivers
       (most likely the latter), when querying the APP table, to
       determine if an APP entry should take effect, or not.
       Additionally, the order of the trusted selectors will dictate
       which selector should take precedence, in the case of multiple
       different APP table selectors being present.

COMMANDS

       show   Display all trusted selectors.

       set    Set new list of trusted selectors. Empty list is
              effectively the same as removing trust entirely.

PARAMETERS

       The following describes only the write direction, i.e. as used
       with the set command. For the show command, the parameter name is
       to be used as a simple keyword without further arguments. This
       instructs the tool to show the values of a given parameter.

       order SEL-LIST
              SEL-LIST is a space-separated list of selector names.
              Possible selector values are: ethtype, stream-port, dgram-
              port, port, dscp, and pcp

EXAMPLE & USAGE

       Set trust order to: dscp, pcp for eth0:

       # dcb apptrust set dev eth0 order dscp pcp

       Set trust order to: port (stream or dgram), pcp, ethtype for
       eth1:

       # dcb apptrust set dev eth1 order port pcp ethtype

       Show what was set:

       # dcb apptrust show dev eth0
       order: port pcp ethtype

EXIT STATUS

       Exit status is 0 if command was successful or a positive integer
       upon failure.

SEE ALSO

       dcb(8), dcb-app(8)

REPORTING BUGS

       Report any bugs to the Network Developers mailing list
       <netdev@vger.kernel.org> where the development and maintenance is
       primarily done.  You do not have to be subscribed to the list to
       send a message there.

AUTHOR

       Daniel Machon <daniel.machon@microchip.com>

COLOPHON

       This page is part of the iproute2 (utilities for controlling
       TCP/IP networking and traffic) project.  Information about the
       project can be found at 
       ⟨http://www.linuxfoundation.org/collaborate/workgroups/networking/iproute2⟩.
       If you have a bug report for this manual page, send it to
       netdev@vger.kernel.org, shemminger@osdl.org.  This page was
       obtained from the project's upstream Git repository
       ⟨https://git.kernel.org/pub/scm/network/iproute2/iproute2.git⟩ on
       2024-06-14.  (At that time, the date of the most recent commit
       that was found in the repository was 2024-06-11.)  If you
       discover any rendering problems in this HTML version of the page,
       or you believe there is a better or more up-to-date source for
       the page, or you have corrections or improvements to the
       information in this COLOPHON (which is not part of the original
       manual page), send a mail to man-pages@man7.org

iproute2                    22 November 2022             DCB-APPTRUST(8)

Pages that refer to this page: dcb(8), dcb-rewr(8)

---